is a Zigbee gateway implementation that follows the standard Zigbee 3.0 specification (and earlier revisions). ZHA integration Integrations connect and integrate Home Assistant with your devices, services, and more. There is also support for native on-device Zigbee binding and unbinding (i.e. At least two entities must be added to a Zigbee group inside the ZHA integration Integrations connect and integrate Home Assistant with your devices, services, and more. In addition, it has support for “Zigbee groups” that enable native on-device grouping of multiple Zigbee lights, switches, and fans that enable controlling all entities for those devices in those groups with one command. currently supports the following device types within Home Assistant: This integration Integrations connect and integrate Home Assistant with your devices, services, and more. All coordinators compatible with zigpy can be used with ZHA. ZHA uses an open-source Python library implementing a hardware-independent Zigbee stack called zigpy. allows you to wirelessly connect many off-the-shelf Zigbee-based devices directly to Home Assistant, using one of the many available Zigbee coordinators. That is, is it possible to compile TI Z-Stack 3.The ZHA (Zigbee Home Automation) integration Integrations connect and integrate Home Assistant with your devices, services, and more. However, might not CC253x based hardware be good enough to in most cases be used as fully Zigbee 3.0 compliant router devices if they could run TI Z-Stack 3?Ĭould Z-Stack 3 (3.0.x / 3.x) router application firmware be compiled for CC253x based USB sticks/dongles? I understand that CC253x based hardware is not recommended by Zigbee2mqtt developers to use as a Zigbee 3.0 coordinator hardware as the MCU in those chips might not be powerful enough to run the TI Z-Stack 3 coordinator firmware without performance-related issues. Is it even possible to use CC2530/CC2531 hardware as a Zigbee 3.0 router with TI Z-Stack 3 firmware? Zigbee 3.0 provides backward compatibility with other Zigbee application profiles such as Zigbee Light Link 1.0 profile, Zigbee Home Automation 1.2 profile, etc. For example, device#1 from Zigbee Light Link profile can coexist with device#2 from Zigbee Health Care profile with same Zigbee 3.0 network. Due to this, Zigbee 3.0 allows devices from different application areas to communicate and form single homogeneous network, including allowing Zigbee 3.0 devices to act as a router for other Zigbee 3.0 devices that are using a different "Zigbee Application Profile". The important outtake from this is that the Zigbee 3.0 specification enables interoperability among those different "Zigbee Application Profiles".
![what stack does x lite softphone use what stack does x lite softphone use](https://i.ytimg.com/vi/06RabhKxD3w/maxresdefault.jpg)
the full Zigbee 3.0 protocol stack), also known by their different "Zigbee Application Profiles" names.
![what stack does x lite softphone use what stack does x lite softphone use](https://smartheart.in.ua/sites/default/files/x-lite-voip-softphone-calls-over-ip-2.jpg)
I know that a ZHA 1.2 router can already be used in Zigbee 3.0 networks, and I also understand that many (if not most) devices can run in ZHA 1.2 backwards-compatibility mode, but I believe that those Zigbee 1.2 routers are then limited to only route the ZHA 1.2 (Zigbee Home Automation) protocol/profile and not other Zigbee 3.0 and Zigbee PRO protocols/profiles (i.e. Main scenario I am personally thinking about that could great benifit the community is repurposing CC2530/CC2531 USB sticks/dongles that you already own when upgrading newer Zigbee coordinator hardware, plus the fact that CC2530/CC2531 USB sticks/dongles cost a lot less than newer Texas Instruments Zigbee coordinators if you want TI sticks as your Zigbee routers. The reason is that that many users are now asking if it is possible to use cheap CC2530 and/or CC2531 hardware adapters as fully compliant Zigbee 3.0 router hardware in a Zigbee 3.0 network. That is, base a Zigbee router firmware for CC253x on Z-Stack 3 (3.0) instead of the older Z-Stack Home 1.2 stack? Any chance that you could release Z-Stack 3.0.x router firmware files for CC253x (CC2530/CC2531) USB sticks/dongles?